1000cc Trophy Kart Build Pt. 3 | Mounting the Rear Axle

  Դիտումներ 156,680

CarsandCameras

8 ամիս առաջ

We build the beginning of a dashboard for the 1000cc BMW powered Trophy Kart! We were especially careful to leave PLENTY of room for feet & legs. We also mounted the rear differential! Out solid axle is from a 1981 Chevrolet Chevette. It's heavy, but it ought to be absolutely bulletproof for reliably putting the BMW K100's 90 horsepower to the ground.
Thanks for Watching!

Facebook: goo.gl/VR6mh2
Instagram: goo.gl/PqOIo3

Go Power Sports: goo.gl/c2Tz6o
NEW MERCH: www.cars-cameras.com/
Equipment we use: www.amazon.com/shop/carsandcameras

The following video features activities performed in controlled environments by knowledgeable persons. DO NOT attempt to duplicate, re-create, or perform the same or similar activities at home, as personal injury or property damage may result. CARS AND CAMERAS, the persons shown in this video and ANY CONTRIBUTOR, ARE NOT LIABLE FOR ANY such injury or damage. ALL CARSANDCAMERAS CONTENT IS FOR ENTERTAINMENT PURPOSES ONLY.

Cars and Cameras makes no representation about the sufficiency of any safety precautions and equipment used in this video.

Մեկնաբանություններ
Dwight Schrute
Dwight Schrute 4 ամիս առաջ
Please, add some foam seats and foam under that cross bar so you have some level of comfort and do not bruise your shin bone
i am No one
i am No one 5 ամիս առաջ
could use the bmw rear diff thingy to make another amphibious built. reverse trike configuration too.
bill dursa
bill dursa 6 ամիս առաջ
If the driveshaft turned the opposite direction all you need to do is flip the diff over like they did on some old race cars with a reverse rotation cam so when the engine torqued the left front tire would pull down.
John Smith
John Smith 6 ամիս առաջ
I am building a trike out of the same engine. Not a reverse trike, ha. Thank you for the info.
Vanagon Adventures
Vanagon Adventures 7 ամիս առաջ
Weld the diff!
Lockeyest Locksmith
Lockeyest Locksmith 7 ամիս առաջ
Henry Ford’s mid30s suspension system had over 9 inches of travel and work very well. Check out Torque tube Drive.
Lockeyest Locksmith
Lockeyest Locksmith 7 ամիս առաջ
I know this is probably too late but do not use parallel four Bar rear suspension. Use triangulated four Bar system, there are A lot of designs. These systems allow the rear wheels to move independently , Parallel four bar works well with drag racing requirements but not off road requirements, I found this out the hard way while working on a 48 Ford rear suspension, while I had the parallel four bar mocked up I discovered that when one wheel hit a bump the other wheel moved up The same distance, not staying on the ground. A triangulated four Bar System can deliver nearly independent suspension action. Mock it up and see for yourself.
Dwight Schrute
Dwight Schrute 7 ամիս առաջ
Vw bug engine on a small go kart
Dylan Schmidt
Dylan Schmidt 7 ամիս առաջ
Not expecting a reply to this but do you happen to know what year model that chevette rear end was from? I'm needing an 81 chevette scooter driveshaft it's a 4speed manual
Fish R Relaxing
Fish R Relaxing 8 ամիս առաջ
Looks like a Jeep ax4 transmissions to np231/241 input shaft would be the right spline count, diameter and length but you’d have to have it drilled and taped on one end to accept a yoke. In fact if you wanted to go 4wd I’m betting you that you could mount a np231 directly up to that transmission output shaft lol.
mfowler15
mfowler15 8 ամիս առաջ
Y’all should check out how real prerunners do steering and build a swingset setup
David Kelm
David Kelm 8 ամիս առաջ
Dope Nasty 🧔 " BMVETTE "
Caleb Harron
Caleb Harron 8 ամիս առաջ
Now all you guys have to do is put a K24 in a cart
RC Hysteria
RC Hysteria 8 ամիս առաջ
snowmobile shocks!
Dirty Dangles
Dirty Dangles 8 ամիս առաջ
Hey i think you should cut off the factory spring pot , leaving that part on the rear axel makes it look real ghetto just cut it off and weld some tabs plus you will get better geometry with the hyme closer to the axel
James Hopper
James Hopper 8 ամիս առաջ
What is the plan for axle wrap. Triangulated link setup would work well for the back. Then the front you can build your own A-arms. Put that bender to work lol.
Steve Roach
Steve Roach 8 ամիս առաջ
What's next ??? Build a v-6 auto from likes parts turbo it & will be a beast using car parts !! Parts would be cheap & it would be heavy duty & kick ass !!!!
Matt
Matt 8 ամիս առաջ
Revive the mower with a diesel
TACOMASRT5
TACOMASRT5 8 ամիս առաջ
I'm building a predator 6.5hp golf cart. Would I be better off with clutch or torque converter?
Robin Damonse
Robin Damonse 8 ամիս առաջ
hello guys you have taught me alot about engines i hust want to know if go power sports ship to South Africa . Im from Cape Town and what pipe thicken do you use for the karts thanks guys
MikesMiniBikes
MikesMiniBikes 8 ամիս առաջ
Are you guys doing the "not today rona" enduro 100?
Preston Humphrey
Preston Humphrey 8 ամիս առաջ
Are you guys ever gonna do a Tecumseh engine rebuild?
tehbonehead
tehbonehead 8 ամիս առաջ
If you guys keep the three-link, you'll want to replace the panhard rod with a watts link for the travel you've got planned...
tehbonehead
tehbonehead 8 ամիս առաջ
Driveshaft nickname? THE MASHER!
Genetic Fish
Genetic Fish 8 ամիս առաջ
Missed weeks of content because your videos didn't show up in my sub feed. Gonna turn on notifications now. Weird
cracker jack
cracker jack 8 ամիս առաջ
you think you guys can spare a stage 2 performance kit for a poor mans mini bike lmao
Andrew J
Andrew J 8 ամիս առաջ
Put some padding or foam pipe around the metal bars so it won’t reck ur shins
Ayden Schily
Ayden Schily 8 ամիս առաջ
It’s off topic but I had to install a new crank into my predator 212 I put it all back together and now when I pull it, it’s really hard to pull. What would cause it to do that???????
Wesley Purkey
Wesley Purkey 8 ամիս առաջ
After this build it would be really cool to see a rally/Baja chevette build💯
josh salyers
josh salyers 8 ամիս առաջ
I am building a Duramax 440cc go kart what torque converter should I use
Christian Perkovich
Christian Perkovich 8 ամիս առաջ
Its really good to see Ricky Bobby still running around after leaving nascar.
Jimmy Delgado
Jimmy Delgado 8 ամիս առաջ
Hi, why don’t you made a video of the Coleman KT196? 😁👋
IRON LION
IRON LION 8 ամիս առաջ
Any plans on building an engine with the new performance parts from go power sports like the stroker crankshaft
Stephen Uncapher
Stephen Uncapher 8 ամիս առաջ
To bad you couldn’t use a cv axel
ZEBRAN 14
ZEBRAN 14 8 ամիս առաջ
I am just waiting for this build to get finished. I love it❤
Mike West
Mike West 8 ամիս առաջ
Put an amr500 supercharger on it.
Jon Wodziak
Jon Wodziak 8 ամիս առաջ
Comment for support. You guys are kicking ass. Can’t wait to see it done.
G56AG
G56AG 8 ամիս առաջ
The part you removed from the BMW drive shaft is called a final drive, not a differential. A differential is for a vehicle with 2 rear wheels, the motorcycle only has one rear wheel so it has a final drive.
Ole van meurs
Ole van meurs 8 ամիս առաջ
Is there ever gonna be a new drag rail?
Chance Mahan
Chance Mahan 8 ամիս առաջ
i’m trying to get into building go karts myself, could someone help and tell me what the gas milage is on a average 1 to 2 seater 212 predator engine go kart ? much appreciated for the help
JTL
JTL 8 ամիս առաջ
A Bathtub on wheels :-D
Richard Hatt
Richard Hatt 8 ամիս առաջ
am-posts.info/list/pJvIvYLAuZSqrqQ/video
Richard Hatt
Richard Hatt 8 ամիս առաջ
You need to get an Amphicat type vehicle for your pond.
ruben bubbah
ruben bubbah 8 ամիս առաջ
I want to see more of this project! it's getting very good
Wim van de Steeg
Wim van de Steeg 8 ամիս առաջ
think about it...if the rear axle would turn the wrong way, just flip it upsidedown...so never have to worry about that again :) starting to look awesome!!
Kay Ammann
Kay Ammann 8 ամիս առաջ
if the shaft turned the other way you could've just turned around the axle.
James McGee
James McGee 8 ամիս առաջ
Right on guys! I hope you find whatever you need to complete this build. I Can't wait to see this bad boy running.
MrLendermanGaming
MrLendermanGaming 8 ամիս առաջ
You guys should build a small predator powered PunkinChunker in your property to see if gopwersports and some magic might help them fly further!
Cybertronian Exchange
Cybertronian Exchange 8 ամիս առաջ
Really wish y'all went with the reverse trike for this. That would have been awesome. Seeing that offset drive shaft, you should put in a 4wd transfer case and throw an old claw foot tub in between the frame for seating. It will be the bath tub bouncer.
mark smithson
mark smithson 8 ամիս առաջ
You guys stay safe and healthy. Keep it going guys and it'll be fine!!
Russell Talbot
Russell Talbot 8 ամիս առաջ
If the rotation was wrong you could have flipped the axle over.
Tommy 143498
Tommy 143498 8 ամիս առաջ
What kind of turbo is on your turbo mini trike
Isaac it'll be fine
Isaac it'll be fine 8 ամիս առաջ
Ebay
Emiliano Ortiz
Emiliano Ortiz 8 ամիս առաջ
Hey bro we want to see a power wheels build
SosnowskiJORDAN
SosnowskiJORDAN 8 ամիս առաջ
I love these big build series you guy do 😎
Jeff Jankiewicz
Jeff Jankiewicz 8 ամիս առաջ
I wondered what you guys were going to do with Ike`s Chevette rear, lol mystery solved. This is gonna get sketchy............and I love it!
GodschildinNC
GodschildinNC 8 ամիս առաջ
Put a rear hoop up to the triangulated supports. Rather B Welding could help with a splined shaft.
Brad Furniss
Brad Furniss 8 ամիս առաջ
I have a steering rack out of a polaris rzr 1000 you can have. Just pay for shipping.
Slim Sqde
Slim Sqde 8 ամիս առաջ
5:59 when she pulls down my pants😂😂
V8 POWER!
V8 POWER! 8 ամիս առաջ
Maybe power steering on this build? That would be a challenge but very worth it!
Mimmi 205
Mimmi 205 5 ամիս առաջ
Easier way put civic electric power steering (mk7)
Nitewatch 1967
Nitewatch 1967 8 ամիս առաջ
Use hydraulic steering
Jacob Kennedy
Jacob Kennedy 8 ամիս առաջ
It's not a pan-hard bar. lol. it's pronounced "Punnard." It's French, from the Panhard automotive company, which turned into Citroen.
Alan Field
Alan Field 8 ամիս առաջ
Between the long snout of the pinion on that axle and the small drive shaft off the motor I fear your notl going to get the suspension droop your looking for to get a smooth ride at high speeds. Wouldn't it be best to pull the small drive shaft for a longer one with u joints or look in to a different axle with a smaller pinion snout. I completely understand the Chevette axle it's probably the narrowest axle you could find. I'm just trying to see it work as you explained and I'm only seeing a 4 to 6 inch droop.
Jente Gerlings
Jente Gerlings 8 ամիս առաջ
Clean the rear dif plz!!
nitrocarnivalSSS
nitrocarnivalSSS 8 ամիս առաջ
Cant wait to see how this project turns out!! Although, Miata shocks and coil-overs aren't gonna give you the plush, long travel suspension that your wanting and that this chassis needs. Miata suspension is made for a 2,000 pound car and at the most have 5 inches of travel. Go on eBay and get yourself some used shocks off a Polaris RZR or equivalent SxS. They are around the same price as used Miata suspension and will give you a lot better ride then any car shock will. Keep up the good work!
Gavin Barnum
Gavin Barnum 8 ամիս առաջ
You guys should build a moped. I have one, its tons of fun at 30mph its an xg470
Damien Thomas
Damien Thomas 8 ամիս առաջ
hey guys ,see if you can get a vw front end out of an old bug ,should be able to find a bome somewhere there and just take the whole front and you got your steering and independent all in one shot ,to bloody easy fellas
willowbrook hermit
willowbrook hermit 8 ամիս առաջ
My go cart Has 85 year-old parts.But is fun.Good job Thank you Enjoy.I have everything you need to fix up thing with.
Filip Munk
Filip Munk 8 ամիս առաջ
make the steering like on an old traktor, well if it will look right ofc.
Edward Werick
Edward Werick 8 ամիս առաջ
I'd suggest changing the torque tube mount so it pivots vertically. The stock rubber isolator won't have enough flex for the suspension travel you want. You could do it easily by trimming the stock mounting plate and welding on a washer to each side vertically. Add pieces of angle to the mounting plates on the frame and bolt the washers to them loosely so they will pivot. If you use the torque tube as a suspension link, you won't need to add 4 more links. In fact, it will probably cause binding. The tube will control pinion and brake torque as well as forward and reverse thrust. The coil overs will control roll and jounce. I would extend the outer suspension links to pivot on the same axis as the front torque tube mount to control yaw. BTW the gear ratio of the Chevette rear should be 3.36:1. Also, Chevette brakes really SUCK. Consider changing to disc brakes. Nice start on this build!
David J
David J 8 ամիս առաջ
Can you guys make a motorized bed frame? I want to improve my bed-to-fridge efficiency
Robert Witherington
Robert Witherington 8 ամիս առաջ
Y’all need to check out rather b weldings grave Ninja build, his front suspension design is something like what y’all need to use on yours.
Lane Hittle
Lane Hittle 8 ամիս առաջ
Vw bug front shocks new on eBay there super cheap
stoned survival 420
stoned survival 420 8 ամիս առաջ
What kinda of roll cage are u guy building on the trophy kart
JackChillz
JackChillz 8 ամիս առաջ
Where’s the mower?
Tyler Smith
Tyler Smith 8 ամիս առաջ
Hey do you guys have any upgrade parts for a predator 212 laying around? Just bought one and I don’t have the money to buy them brand new
YoshinoyaJones
YoshinoyaJones 8 ամիս առաջ
How much for the diff. Why not a 3 wheel reverse trike off road monster?!?!
Chevette 76
Chevette 76 8 ամիս առաջ
Good using the chevette rear end
Ben Baribault
Ben Baribault 8 ամիս առաջ
5:54 My wife on our wedding night getting down to business
Tara Wilkes Jordan
Tara Wilkes Jordan 8 ամիս առաջ
I have a few of some brigs engines if you want them
Julie Waite
Julie Waite 8 ամիս առաջ
I'll take k diff I'm building a trike please
Steven Woods
Steven Woods 8 ամիս առաջ
What would yall thank about turning a miata into a go kart? I thank yall would have lots of fun do that. And you can find there cheap.
Steve Simon
Steve Simon 8 ամիս առաջ
If you pull that drive shaft you will have a u joint at the motor. You should be able to go from there all the way back to the rear end. That is how motorcycle trike kits are engineered. It should be a lot stronger. Also if you look that short drive shaft may be a rubber cushion and won't handle that rear end with out slipping.
David Geier
David Geier 8 ամիս առաջ
Is the plan to have actual trophy truck rear suspension? That would be the coolest part of the build imo.
Chris McCammon
Chris McCammon 8 ամիս առաջ
Damn guys, you're builders!
Eli Renigar
Eli Renigar 8 ամիս առաջ
Y’all should remove that goofy extension on the axle, it’s gonna really limit yalls travel having to build around that cause there’s a lot of travel potential in this build
Nff
Nff 8 ամիս առաջ
To get that amount of travel from a miata coilover you will need to do a pushrod system with ratioed rates. 6 inches of strut travel multiplied into 18 inches of axel travel.
Nff
Nff 8 ամիս առաջ
You need a 4:1 minimum ratio to deal with the 4.5 inches of stroke on the miata coilovers and need to be set to sit 2 inches into the shocks travel to maintain that equlibriem so the rear maintains its 9 of comprssion and 9 of sag. As far as linkage for the rear end go 4 link 2 on the bottom out wide and 2 on the top close to center. Will allow for large flex and articulation. If ya need some insperation look at r/c scale crawlers suspention setups. Oh and loose the torque tube on the dif it wont allow the dif to move vurtically it will cause arching in the travel.
Avetho Plays
Avetho Plays 8 ամիս առաջ
CarsAndCameras (in 15 years, probably): _"In this video we take apart our LMP1 Kart to send it to Germany for a lap around the Nürburgring Nordschleife."_ CarsAndCameras (maybe in a couple months if they are feeling daring enough): _"In this video we take our 1000cc Trophy Kart down south to drive the same roads as the Baja 1000."_
sbluke55
sbluke55 8 ամիս առաջ
I would skip the 4 link and run a trailing arm setup and connect the mounts at the same spot as the front u joint off the trans. Then use the torque tube as a center mount to keep everything working. As for the drive shaft. Remove it from the trans and have the end cut off and make a short section to adapt to the rear end.
It’s Lane
It’s Lane 8 ամիս առաջ
You could go and get some dirt car shocks and springs and see how that’d work?
William Wages
William Wages 8 ամիս առաջ
this thing is going to be awesome when its done
Whomagoose
Whomagoose 8 ամիս առաջ
I still have my 1980 model Chevette. Brand new price of $5300 from the Chevrolet dealer. Purchased in November 1979. Has a 4-speed manual transmission with a two barrel Holly carburetor. Anybody want it?
Isaac it'll be fine
Isaac it'll be fine 8 ամիս առաջ
Your not in nc are you? Lol
Shawns Derby den
Shawns Derby den 8 ամիս առաջ
I still think ur using to thin of tubing hopefully it works out for u guys
Brandon Boyce
Brandon Boyce 8 ամիս առաջ
Instead of Miata coilovers, why not use Fox Nitro shocks. They are about $250 a piece, and act as a spring as well! We have them on our dune buggy, and they are phenomenal.
Leo
Leo 8 ամիս առաջ
I love your channel you look like the two guys from 30 minutes or less
Tampa Boys Customs
Tampa Boys Customs 8 ամիս առաջ
Those tires look so sick on there great work fellas this thing is going to be super sweet
Lennard Stieltjes
Lennard Stieltjes 8 ամիս առաջ
I want the rear dif from the bike🤩, can you send it to the Nederlands!?
Devon motorcycle mechanic
Devon motorcycle mechanic 8 ամիս առաջ
So if u just put on the original rear instead of m8d engine it'll be mind tire. Lol
james ormand
james ormand 8 ամիս առաջ
that thing is going to twist frame
Hard luck
Hard luck 8 ամիս առաջ
You could use an electric steer assembly from an 05 chevy Malibu possibly
Robert Salamun
Robert Salamun 8 ամիս առաջ
New name for this thing! The Castrator! Because when the driveshaft lets go while straddling it, all will be over with! At full rip!
Building a 1000cc Mini Trophy Truck Pt. 4
12:24
CarsandCameras
Դիտումներ 144հզր
Our Mini Trophy Truck Build RUNS!! 1000cc Trophy Kart Build Pt. 13
19:24
Full Face Using FROZEN Makeup Challenge 🥶
14:47
James Charles
Դիտումներ 7մլն
EMBRACING CHANGE | Building our Home at Cabin in Woods
27:08
Eamon & Bec
Դիտումներ 528հզր
jim's office pranks over the years
0:23
Gus Johnson
Դիտումներ 968հզր
Make a Motorised Drift Trike with Basic Tools
17:15
colinfurze
Դիտումներ 8մլն
1000cc Trophy Truck Build Pt. 9 | Steering Finished!
14:01
CarsandCameras
Դիտումներ 149հզր
550cc Go Kart Gets Side Pipes and Fully Sent!
11:44
CarsandCameras
Դիտումներ 519հզր
Collab With Cars and Cameras, Red Beard's Garage & Junkyard Digs!!!
18:24
CHAINSAW GO KART! - Part 1
24:07
This Old Tony
Դիտումներ 3.3մլն
4X4 Ford Bronco Power Wheels Go Kart Pt. 2
16:35
CarsandCameras
Դիտումներ 186հզր
4WD 1000cc Power Wheels Build Series 10. Rolling Chassis Complete!
20:28
Grind Hard Plumbing Co
Դիտումներ 718հզր
4WD Power Wheels Go Kart Build Pt. 3 | Trailing Arm Rear Suspension
21:07
1000 Horsepower 4 Cylinder Engine Teardown Disassembly
14:11
PapadakisRacing
Դիտումներ 1.6մլն
Full Face Using FROZEN Makeup Challenge 🥶
14:47
James Charles
Դիտումներ 7մլն
EMBRACING CHANGE | Building our Home at Cabin in Woods
27:08
Eamon & Bec
Դիտումներ 528հզր
jim's office pranks over the years
0:23
Gus Johnson
Դիտումներ 968հզր
What was your first job? KFC
0:31
Social Trend
Դիտումներ 3.1մլն
Welcome to Gardena 13 and Paybacc Crips hood
11:48
HoodVlogs
Դիտումներ 358հզր
TRAPPED in an INESCAPABLE Car!! *SURVIVAL Challenge!!*
14:09
Team Edge
Դիտումներ 861հզր
Buying a excavator tilt bucket
9:22
Andrew Camarata
Դիտումներ 366հզր
We Put Lambo Doors on the Off-Road Lamborghini Huracan!
20:20
B is for Build
Դիտումներ 304հզր