1000cc Trophy Truck Build Pt. 9 | Steering Finished!

  Դիտումներ 150,021

CarsandCameras

6 ամիս առաջ

We get the steering figured out on our 1000cc BMW K100 powered mini trophy truck build! Building steering with minimal bump steer would've been simple with this custom twin I beam front suspension setup if we only had six inches of suspension travel. However, we have over twelve inches, so we had to test fit, modify, re-weld, cut, modify, etc until we were happy with it.
Thanks for Watching!

Facebook: goo.gl/VR6mh2
Instagram: goo.gl/PqOIo3

Go Power Sports: goo.gl/c2Tz6o
NEW MERCH: www.cars-cameras.com/
Equipment we use: www.amazon.com/shop/carsandcameras

The following video features activities performed in controlled environments by knowledgeable persons. DO NOT attempt to duplicate, re-create, or perform the same or similar activities at home, as personal injury or property damage may result. CARS AND CAMERAS, the persons shown in this video and ANY CONTRIBUTOR, ARE NOT LIABLE FOR ANY such injury or damage. ALL CARSANDCAMERAS CONTENT IS FOR ENTERTAINMENT PURPOSES ONLY.

Cars and Cameras makes no representation about the sufficiency of any safety precautions and equipment used in this video.

Մեկնաբանություններ
T34 The American heavy tank
T34 The American heavy tank 8 ժամ առաջ
I like the pole barn style, the fresh wood with brand new sheet metal looks nice and simplistic
Mort Neff
Mort Neff 3 ամիս առաջ
OK, I know this is a bit late but just thinking of the MG midget stiring.
Charles Sexton
Charles Sexton 3 ամիս առաջ
You might want to go with a 12 inch slab for better anchoring of the beams.
Ben Fouts
Ben Fouts 3 ամիս առաջ
I know it’s a little late but the newer side by sides have a esp steering system maybe something to check into
ShortStroke
ShortStroke 3 ամիս առաջ
I beam!
ryan g g
ryan g g 4 ամիս առաջ
eye beam
Jeff Polsene
Jeff Polsene 4 ամիս առաջ
Well once again I find my self a bit in the rears as far as timing goes, I have just recently started watching your channel but I also have some comments that may be helpful. You mentioned you are going to build a bigger shop. Awesome, you will not regret it. You also asked what we thought about the type of building you should build. Its my opinion that the most bang for the buck is a pole building. Im from Wisconsin, but live in Arizona now, and Wisconsin has maybe more pole buildings than any other state.lol Poole buildings are as permanent as any building, and the cost is far less than many other styles. They can be insulated easy, and are very low maintenance. The key no matter what you choose is having it well insulated. The better the insulation, the easier it is to heat/cool. Either way, glad to hear you are going with a new shop.
Deland Brooks
Deland Brooks 4 ամիս առաջ
Do the red iron shop. Build it 40 X 40 and leave room to expand the length. I've never heard anyone say they wish they had built smaller. Put in a much larger electrical service than required so that it doesn't have to be redone to expand. Also a covered apron outside for extra work area. A wash rack area outside means you can clean parts before bringing them in which keeps the shop cleaner. Just some of the things I plan if I'm ever able to build my "Dream Shop".
Michael Leeper
Michael Leeper 4 ամիս առաջ
Wish it was a 2 seater were both of you could ride
Meifesto
Meifesto 4 ամիս առաջ
Probably a bit late, but wouldn't it be wise to build it close/against the already existing building, so opening those two up could be a option in the future?
Surfzap63
Surfzap63 4 ամիս առաջ
I enjoy the reality of the live and learn build lessons. Working out of your comfort zone and teaching us at the same time is admirable and difficult I am sure. I appreciate your efforts.
Jason Hancock
Jason Hancock 5 ամիս առաջ
If it were me you have more than half of your slab I would just build around your old shop then tare down the old why waste the room.
Boss the dog
Boss the dog 5 ամիս առաջ
I Beam
Pegleg metalhead
Pegleg metalhead 6 ամիս առաջ
Guys look into VW sandrail rack and pinions
John Cook Outdoors
John Cook Outdoors 6 ամիս առաջ
I've used a steering setup off a center console boat before, worked decent
Sean Athair
Sean Athair 6 ամիս առաջ
Build the slab 50'x50' so you can expand later, and until then you'll have a usable outdoor area to work or store
Mr B
Mr B 6 ամիս առաջ
Redbeard's garage copied your entire channel, might as well copy his building. It's nice, check it out.
Broo_sh
Broo_sh 6 ամիս առաջ
Jonh & Ike Just Go Ask In JunkYards Do They Have Materials To Give Free And Also Put Ads In Internet (Facebook / Local News Paper / Store info board/info Walls I bet You Gonna Get Messages Or Calls In Many Peoples Who Have AllKinda Materials To Give Free Or Low Price
Jerry Shirley
Jerry Shirley 6 ամիս առաջ
Try a golf cart steering box
Te Mawae McAllister
Te Mawae McAllister 6 ամիս առաջ
i think some tube wheel arches would look sick on this
bill dursa
bill dursa 6 ամիս առաջ
Mount the tie rod ends on top of the spindles, maybe? Might help the bump steer.
Christian Buczko
Christian Buczko 6 ամիս առաջ
Why is the steering so complicated???? I also think it may struggle to turn right, and try to steer left, as it seems weighted in favour of a left turn..
Jeffery Allison
Jeffery Allison 6 ամիս առաջ
Red iron building! Also, go 16’ walls and a 14’ door, this will let you park large equipment or a motor home in there later. Future proof it.
Page Harris
Page Harris 6 ամիս առաջ
you could go with a electric assist stearing from a utv
Seth Carpenter
Seth Carpenter 6 ամիս առաջ
Steering Box from a Sprint Car would probably work really well for this. Lightweight but a little high unless you can find a used one
Wayne Padget
Wayne Padget 6 ամիս առաջ
If you can funds can swing it John, Go I Beam, as you and Isaac are going to be working in it for a long time, so you want it to last, All The Best From Australia.
Chris Hinds
Chris Hinds 6 ամիս առաջ
All i ask is that we get a full build series on the new shop!!!!!!!
dirthaloboy
dirthaloboy 6 ամիս առաջ
You guys should do an episode on a build with this mini nos kit. www.6sigmajetkit.com/nitrous-kits.html
Charles Baunsgard
Charles Baunsgard 6 ամիս առաջ
Take a look at the miracle truss buildings. They are clear span and great for shops.
ronald kleinow
ronald kleinow 6 ամիս առաջ
VW bug or chevy vega. There is another system where you use matching 2way cylinders like from a convertible top cylinder and you drive one with the steering wheel and use the other as a remote cylinder when you turn the wheel it just pushes the displaced fluid to the other cylinder by transferring the fluid back and fouth. The transfer lines must be as large of diameter as possible.
Ryan M
Ryan M 6 ամիս առաջ
Pole barn! Or ibeam
Michael Renzi
Michael Renzi 6 ամիս առաջ
Automatic garage doors on a Morton style building facing the pond
The motorsports project
The motorsports project 6 ամիս առաջ
Just curious as to why you are not using rack and pinion steering on this?
Mike Csokuly
Mike Csokuly 6 ամիս առաջ
An old vw bug steering box And it’ll be fine
Joes welding
Joes welding 6 ամիս առաջ
Keeping getting bigger and better anyone who likes u small is kinda holding you back in my opinion
W a b b i t
W a b b i t 6 ամիս առաջ
I think they’ve been pushing the “it’ll be fine” a bit too far on this one
jiggy chad neuman
jiggy chad neuman 6 ամիս առաջ
They master building machine like this they could make ton of money doin that selling sum to the public
stempo1
stempo1 6 ամիս առաջ
Use the rack from the junk Miata
THEDIRTYFERDY
THEDIRTYFERDY 6 ամիս առաջ
Cardone Remanufactured Steering Boxes 27-6507 or part number AAZ-27-6507
boltonky
boltonky 6 ամիս առաջ
Good series, My thing with workshops is its not the size but does everything fit in....Think ahead car lifts, drills, press, welders etc etc all take up space also having things modular is wicked. Also final point is an overhead crane...i know you boys can get tractors etc all cheap in the US for lifting but better to be sorted
Raymond Bliss
Raymond Bliss 6 ամիս առաջ
North east dirt modified race car steering box wold be perfect
Stephen Hinson
Stephen Hinson 6 ամիս առաջ
Tried different brands of golf carts for your steering needs
Jeff Hanson
Jeff Hanson 6 ամիս առաջ
Hi way dont you try a motorcycle junk yard and you met have more sexes to get a string box for your build to jeff hanson
Judi Barclay
Judi Barclay 6 ամիս առաջ
try a chevy vega steering box
Chad D
Chad D 6 ամիս առաջ
Im not sure I understand the music choices =p . Never consistent and always different genres .
Import cars are life
Import cars are life 6 ամիս առաջ
What about a golf cart steering box
Nick Miller
Nick Miller 6 ամիս առաջ
in edge water florida
Nick Yarnot
Nick Yarnot 6 ամիս առաջ
Just use a small electric power steering setup from a 4x4 quad?
powerbuilder0
powerbuilder0 6 ամիս առաջ
silver/grey corrugated iron roof/walls shed, top hat or Z purlin roof bearers, 50x100 mm Galv C channel open sides facing together to make a square post with no open sides welded together every foot or so. top hat or Z purlins screwed horizontal to the post with silver galv corrugated iron vertical, carton of purlin bolts and roofing screws. C channel with holes drilled to hammer round bar for form work and pour concrete in sections for easy DIY
mechniack
mechniack 6 ամիս առաջ
You guys need a milling machine, and a lathe
B Dubz
B Dubz 6 ամիս առաջ
I-Beam style, steel exterior. My father had one built once that was converted into half of his house and the other half into an airplane hangar. Surprisingly the building was very versatile, efficient when insulated, and after 35 years still stands today and in every bit of good shape as when it was built. Part of my fathers hangar side of his I beam building he used for restoring muscle cars, and fabricating chassis for race cars. We devised a ton of neat stuff into some of the buildings beams, like an engine hoist, car lift, and holding up the upper level office floor. Versatile.
Captain Land Yacht
Captain Land Yacht 6 ամիս առաջ
RV height carport style with spray insulation, as you can hack into it and add on with little regret over the years. Second story party pad with inside and outside entrance/exit, built with good old fashioned lumber. Steel a frame hoist on track bolted to floor. Solar array with battery bank. Use 220v water heater powered from solar to heat the floor. 220v AC from solar in the summer.
Matt Carlson
Matt Carlson 6 ամիս առաջ
Need a collaboration with these guys am-posts.info #TexasBarndominiums!
why ?
why ? 6 ամիս առաջ
30 by 50 is super small. Build like a 100 by 80 or something
Joe
Joe 6 ամիս առաջ
i bet if you searched randoms side by side models for steering boxes one of them out there might have what you want
Alan Casey
Alan Casey 6 ամիս առաջ
Red I beam
Louman 75
Louman 75 6 ամիս առաջ
I would go for a carport style garage because it’s the most traditional and I personally think it looks the best
sean bragg
sean bragg 6 ամիս առաջ
Jeep jk steering box aluminum part# 52126348AA
Dalton England
Dalton England 6 ամիս առաջ
Wheelchair gocart?
Gerald Klassen
Gerald Klassen 6 ամիս առաջ
Yamaha wolverine and rhino have EPS. Electronic power steering. real strong and should do the trick. Also the red i beam is the way to go.
Groovey Grubworm
Groovey Grubworm 6 ամիս առաջ
In Virginia if you build a pole building you don't have to worry about getting it inspected. Not sure how it works in North Carolina
spike army
spike army 6 ամիս առաջ
So ive been having a problem with my mini bike. When i try to get it up to speed it starts sputtering and doesnt go full speed. Idk why that is. Its a 212cc with a 22mm mikuni carb and a header pipe. Please help me thanks
Tjitse Schilstra
Tjitse Schilstra 6 ամիս առաջ
Complicated systems 🤔
FaithfulMC
FaithfulMC 6 ամիս առաջ
Just make sure the shop is tall enough for a lift
lurgy1
lurgy1 6 ամիս առաջ
your front suspension is "independent" !!!
Big Foot
Big Foot 6 ամիս առաջ
Cars and cameras are the Darrel hall and John Oats of go carts!
440 Fishing
440 Fishing 6 ամիս առաջ
Cars & Cameras mask next in line ? 😷
stoned survival 420
stoned survival 420 6 ամիս առաջ
I have a question for Jon have u ever smoke weed and had a great idea for a go kart project lol
Colleen Callan
Colleen Callan 6 ամիս առաջ
Use a rack from a wrecked side by side make two bump steer castles for the tie rod ends at the wheel knuckle
Colleen Callan
Colleen Callan 6 ամիս առաջ
Do away with the cross of the tie rods that will eliminate all the extra bends and hacks you do t need
Brandon Fulton
Brandon Fulton 6 ամիս առաջ
Hey so listen guys, could you give me a tip? So I have a running ninja 500r 6speed, and I wanna turn it into a gokart, what metal do you use for motor mounts? And what wleding material do our suggest?
Gavin Neimeyer
Gavin Neimeyer 6 ամիս առաջ
2 floor chill/living space
Steve Zanatta
Steve Zanatta 6 ամիս առաջ
Use an ATV electric steering Or a steering box from a newer Mini Cooper
mfnman88
mfnman88 6 ամիս առաջ
1st gen toyota prius steering... all electric 12V power steering built into the steering shaft. just needs power and a 12v signal to one pin on its harnes to turn on. $35 at your local salvage yard.
JeezJonas
JeezJonas 6 ամիս առաջ
build a new shop
The 1st beast
The 1st beast 6 ամիս առաջ
can u post every day
The 1st beast
The 1st beast 6 ամիս առաջ
what about the 8 mini bike
josh youngs
josh youngs 6 ամիս առաջ
So switch your knuckles from one side to the other. It would rase the steering point and there would be less travel with the link being closer to in line with the rack. you wouldn't need them to cross over any more.
Thunderray5687
Thunderray5687 6 ամիս առաջ
I beam sounds best.
Thomas Pigg
Thomas Pigg 6 ամիս առաջ
I think the I beam style building would be the way to go. Simple to set up and build. Pretty easy to wire one (just don't get grounded out!!!), and you can always add add on to the sides later if you need to. I also like Micah De Boer's idea of using a VW steering box. A little looking around should find yall one pretty easy. Loved the video Dudes!!! Keep'em coming!!!
minterfab
minterfab 6 ամիս առաջ
Yamaha Grizzly has a electronic power steering unit on them. It would be straight in straight out but it would have power steering on it that is electrically assisted. There is a used one on eBay right now for a hundred and seventy-five bucks. Would be way lighter and less bulky than what you're using
Patrick Tolmie
Patrick Tolmie 6 ամիս առաջ
Hey Isaac John I'm Patrick from Pennsylvania keep up the good work Building self good shop I like watching your videos I ran in a bunch of quads I'll let you know if you're interested in anything or I find a steering box for you my Gmail is Allen tolmie 92 a.com you can contact me anytime keep up the good work guys thanks Patrick
Andrew Brantner
Andrew Brantner 6 ամիս առաջ
How about just a manual gearbox. I think this one is less than 15 lbs. www.summitracing.com/parts/clp-vega-msb
fudgun
fudgun 6 ամիս առաջ
You should get a garage kit from Home Depot. www.homedepot.com/b/Storage-Organization-Sheds-Garages-Outdoor-Storage-Outdoor-Storage-Carports-Garages-Garages/40-x-50/N-5yc1vZbtyoZ1z1bytv/Ntk-EnrichedProductInfo/Ntt-garage?NCNI-5&experienceName=default
CrimsonSky 2019
CrimsonSky 2019 6 ամիս առաջ
will this be for sale after it is finished?
Jake Chunasamy
Jake Chunasamy 6 ամիս առաջ
Does anyone Remeber the 10hp tiny atv does anyone know what it is called I really want it :(
Chris Johns
Chris Johns 6 ամիս առաջ
Chev tracker steering box is small
Jay Defriece
Jay Defriece 6 ամիս առաջ
Bigger is better please
William Griffith
William Griffith 6 ամիս առաջ
I beam style for sure Jon
jeff schmidt
jeff schmidt 6 ամիս առաջ
I just built a wooden pole barn. That's just where the budget was. Built probably they will last a lifetime. But if you can swing it go with the I beam. Definitely go bigger than you think you need!
Keaton's carlott
Keaton's carlott 6 ամիս առաջ
I have 1 sitting in my living room. Got it on ebay
Keaton's carlott
Keaton's carlott 6 ամիս առաջ
Golf kart rack n pinions are 70$ new.
nick meijer
nick meijer 6 ամիս առաջ
Why u guys aint use a kirkey racing seat? If you guys wanna jump this i'd prefer an aluminum racing seat with 5point harness...
james knocke
james knocke 6 ամիս առաջ
Hit up ratherbwelding to do a collab maybe even make a better trophy cart
knives357
knives357 6 ամիս առաջ
i beam. you can put crane pulleys off the beams on wheels to use as lifts for engines and what not
K K
K K 6 ամիս առաջ
Pole barn
Liam Fiduccia
Liam Fiduccia 6 ամիս առաջ
I love your vids
frank egan
frank egan 6 ամիս առաջ
Chevy vega gear box had a shorter turn from lock to lock
siccmade425
siccmade425 6 ամիս առաջ
Expand when you need to, and only when you've out grown the space you are in. Don't bite off more than you can chew. You're not Cleetus, and things don't normally go that way. Just be methodical. Build, build, build....
Ben Brown
Ben Brown 6 ամիս առաջ
You could look for a Yamaha grizzly eps part out those have power steering
Disney's Raya and the Last Dragon | Official Trailer
2:29
Walt Disney Animation Studios
Դիտումներ 1.2մլն
70HP Supercharged Harbor Freight Predator 670cc V Twin Engine Build
21:25
Red Beard's Garage
Դիտումներ 1.4մլն
I built a Cabin in 2020 - Start to Finish
28:53
Woodness Goodness
Դիտումներ 2.1մլն
Building an Off-Grid Homestead  ..... start to finish
35:06
Bushradical
Դիտումներ 1.1մլն
How to Fix a Car that Wont Start (I bought it for $500)
30:40
1000cc Trophy Truck Go Kart Build Pt. 11
27:43
CarsandCameras
Դիտումներ 178հզր
I built a guitar out of a SHELF during lockdown !
26:01
tchiks guitars and furniture
Դիտումներ 2.9մլն
Disney's Raya and the Last Dragon | Official Trailer
2:29
Walt Disney Animation Studios
Դիտումներ 1.2մլն
Car Wash on a Ceramic Coating (satisfying)
0:21
Tymo Paints
Դիտումներ 306հզր
Tubing Behind a 500HP JET SKI
17:16
BoostedBoiz
Դիտումներ 170հզր
STRAIGHT PIPING MY MCLAREN AND A BUMPER DELETE! *$10k TITANIUM EXHAUST*
18:09
Arkansas State Police 109 MPH PIT Maneuver | The Complete Pursuit
21:30
Real World Police
Դիտումներ 2.9մլն
BUYING THE RAREST 2006 BANSHEE 350 QUAD ??? | BRAAP VLOGS
20:52
BRAAP VLOGS
Դիտումներ 185հզր
My NEW CAR!! (Bought sight unseen off the internet)
22:57
Mighty Car Mods
Դիտումներ 484հզր